Copper Tube Condenser Heat Exchanger

Copper Tube Condenser Heat Exchanger

High Quality Copper Tube Aluminum Fin Heat Exchanger Coil,Water to Air Heat Copper Tube Aluminum Fins Heat Exchanger Coils

Copper Tube Aluminum Fin Heat Exchanger Coils,Water to Air Heat Copper Tube Aluminum Fins Heat Exchanger Coils

High performance copper tube finned heat exchanger

Good Quality Copper Tube Aluminum Fin Heat Exchanger Coils,Water to Air Heat Exchanger Coils

Type 400*400MM

5kW Heats 385m3 equivalent to 96 m 2 with ceiling height 4 m

Calculated from a temperature at 70/40/20 between well insulated workshop. 13Watt per m2

They are all characterized by:

• All the air passing through the air heater.

• The entire casing is manufactured in galvanized steel plate.

• Can be mounted both horizontally and vertically.

• Hot surfaces are made of copper tubes and aluminium fins. Copper pipes are

extruded in order to guarantee a high level of heat conduction between copper and aluminum.

• Touching with thread made of steel tubes.

• All slats in exhaust jalousiet can be set individually.

• The sickle-shaped fan blade ensures a low noise level.

• 5 sizes with 1 x 230 volt motor

• All motors are with 2 steps.

Fast calculation of the size of the Heat blower:

Insulation

Newer (2010 standards) Factor 10W/m3

Between Factor 13W/m3

Bad Factor 15W/m3

Volume (S)

Heat output (V) V = 10 x s = ____ Watt V = 13 x R = ____ Watt V = 15 x R = ____ Watt

Unit Heater

Type 500*500MM

9, 7KW Heats 745m3 corresponding to 186m2 with ceiling height 4 m

Calculated from a temperatursæt at 70/40/20 between well insulated workshop. 13Watt per m2

They are all characterized by:

• All the air passing through the air heater.

• The entire casing is manufactured in galvanized steel plate.

• Can be mounted both horizontally and vertically.

• Hot surfaces are made of copper tubes and aluminium fins. Copper pipes are

extruded in order to guarantee a high level of heat conduction between copper and aluminum.

• Touching with thread made of steel tubes.

• All slats in exhaust jalousiet can be set individually.

• The sickle-shaped fan blade ensures a low noise level.

• 5 sizes with 1 x 230 volt motor

• All motors are with 2 steps.

Fast calculation of the size of the Heat blower:

Insulation

Newer (2010 standards) Factor 10W/m3

Between Factor 13W/m3

Bad Factor 15W/m3

Volume (S)

Heat output (V) V = 10 x s = ____ Watt V = 13 x R = ____ Watt V = 15 x R = ____ Watt

Unit Heater

Type 600*600MM

 17 .5kW Heats 1345m3 corresponding to 336m2 with ceiling height 4 m

Calculated from a temperatursæt at 70/40/20 between well insulated workshop. 13Watt per m2

They are all characterized by:

• All the air passing through the air heater.

• The entire casing is manufactured in galvanized steel plate.

• Can be mounted both horizontally and vertically.

• Hot surfaces are made of copper tubes and aluminium fins. Copper pipes are

extruded in order to guarantee a high level of heat conduction between copper and aluminum.

• Touching with thread made of steel tubes.

• All slats in exhaust jalousiet can be set individually.

• The sickle-shaped fan blade ensures a low noise level.

• 5 sizes with 1 x 230 volt motor

• All motors are with 2 steps.

Fast calculation of the size of the Heat blower:

Insulation

Newer (2010 standards) Factor 10W/m3

Between Factor 13W/m3

Bad Factor 15W/m3

Volume (S)

Heat output (V) V = 10 x s = ____ Watt V = 13 x R = ____ Watt V = 15 x R = ____ Watt